Jarkom Skenario A

Jarkom 5.6.1 Konfigurasi RIP Dasar (scenario A)

Buatlah rangkaian awal seperti gambar di atas.
Setelah itu kita atur router di CLI nya satu persatu.

Buka router 1 dan klik tab CLI nya, lalu ketik script seperti ini:
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R1
R1(config)#no enable password
R1(config)#no ip domain-lookup
R1(config)#interface fa0/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no shutdown

R1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R1(config-if)#exit
R1(config)#interface s0/0/0
R1(config-if)#ip address 192.168.2.1 255.255.255.0
R1(config-if)#clock rate 64000
R1(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R1(config-if)#exit
R1(config)#line con 0
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#exit
R1(config)#line vty 0 4
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#exit
R1(config)#router rip
R1(config-router)#network 192.168.1.0
R1(config-router)#network 192.168.2.0
R1(config-router)#network 192.168.3.0
R1(config-router)#network 192.168.4.0
R1(config-router)#network 192.168.5.0
R1(config-router)#exit
R1(config)#end
R1#

Jika sudah, klik close dan rubahlah nama switch 1 menjadi R1 LAN.

Sekarang kita setting Router 2 dengan script seperti ini:
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R2
R2(config)#no enable password
R2(config)#no ip domain-lookup
R2(config)#interface fa0/0
R2(config-if)#ip address 192.168.3.1 255.255.255.0
R2(config-if)#no shutdown

R2(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R2(config-if)#exit
R2(config)#interface s0/0/0
R2(config-if)#ip address 192.168.2.2 255.255.255.0
R2(config-if)#no shutdown

R2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

R2(config-if)#exit
R2(config)#interface s0/0/1
R2(config-if)#ip address 192.168.4.2 255.255.255.0
R2(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R2(config-if)#exit
R2(config)#line con 0
R2(config-line)#password cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#line vty 0 4
R2(config-line)#password cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#router rip
R2(config-router)#network 192.168.1.0
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.3.0
R2(config-router)#network 192.168.4.0
R2(config-router)#network 192.168.5.0
R2(config-router)#end
R2#

Jika sudah, klik close dan rubahlah nama switch 2 menjadi R2 LAN.

Lalu kita setting lagi Router 3. Ubah lah namanya menjadi R3 dan buka tab CLI nya lalu tulis script seperti ini:
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R3
R3(config)#no enable password
R3(config)#no ip domain-lookup
R3(config)#interface fa0/0
R3(config-if)#ip address 192.168.5.1 255.255.255.0
R3(config-if)#no shutdown

R3(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R3(config-if)#exit
R3(config)#interface s0/0/1
R3(config-if)#ip address 192.168.4.1 255.255.255.0
R3(config-if)#clock rate 64000
R3(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

R3(config-if)#exit

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
R3(config)#line con 0
R3(config-line)#password cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#line vty 0 4
R3(config-line)#password cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#router rip
R3(config-router)#network 192.168.1.0
R3(config-router)#network 192.168.2.0
R3(config-router)#network 192.168.3.0
R3(config-router)#network 192.168.4.0
R3(config-router)#network 192.168.5.0
R3(config-router)#end
R3#

Klik close dan sekarang kita akan atur IP untuk setiap PC yg terhubung di setiap router.

PC 1

PC 2

PC 3